Operation and care of

We are pleased that you have chosen a Browning Citori Plus trap shotgun. In every way it is a firearm you will be proud to shoot for many years. It is one of an advanced new generation of trap guns with more adjustability and comfort features than any Browning trap gun ever. Take time to follow this manual carefully, and you will gain real advantages that will bring out the best in your shooting ability. 

With a reasonable arnount of care, your Citori Plus should give you many years of dependable, enjoyable shooting. Please feel free to write us immediately if you have any observations regarding its performance and operation. 

Thank you. 

You Are Responsible for Firearms Safety

As a gun owner, you accept a set of demanding responsibilities. How seriously you take these responsibilities can be the difference between life and death. Failure to follow any of these instructions can cause extensive damage to your gun and / or possible serious injury or death to yourself and others. 

There is no excuse for careless or abusive handling of any firearm. At all times handle your shotgun and any other firearm with intense respect for its force, power and potential danger.

PLEASE READ AND UNDERSTAND ALL OF THE CAUTIONS, THE PROPER HANDLING PROCEDURES AND INSTRUCTION OUTLINED ON THIS PAGE BEFORE USING YOUR NEW FIREARM. 

PLEASE READ AND PRACTICE THE FOLLOWING CAUTIONS:

CAUTION

1 - ALWAYS KEEP THE MUZZLE OF YOUR FIREARM POINTED IN A SAFE DIRECTION even though you are certain the shotgun is un­loaded and '' on safe.'' Never point any firearm at anything you do not intend to shoot. Be extremely alert and aware of all persons and property within range of your ammunition.

2 - NEVER RELY TOTALLY ON YOUR SHOTGUN'S MECHANICAL "SAFETY" DEVICE.  

Always assume that your gun can be fired at any time, even with all safety mechanisms en­gaged. The word "safety" describes a gun's me­chanical devices that are designed to place your gun in a SAFER status. No guarantee can be made that the gun will not fire even if the "safety" is in the "on safe" position. See "Op­eration of the Safety" later in this manual for instructions on operation of this gun's "safety." 

LIKE ANY MECHANICAL DEVICE, A "SAFETY" CAN SOMETIMES FAIL; IT CAN BE JARRED OR INADVERTENTLY MANIPULATED INTO AN UNSAFE CONDITION. 

Mechanical "safeties" merely aid safe gun handling and are no excuse for pointing your shotgun's muzzle in an unsafe direction. While it is a good idea to "test" your gun's mechani­cal "safeties" periodically for proper function, NEVER TEST THEM WHILE YOUR FIREARM IS LOADED OR POINTED IN AN UNSAFE DIREC­TION. 

Safe gun handling does not stop with your gun's mechanical "safety" devices - it starts there. Alvays treat this shotgun with the respect due a loaded, ready-to-fire firearm. 

NEVER TEST THE MECHANISM OF ANY FIREARM WHILE IT IS LOADED OR POINTED IN AN UNSAFE DIRECTION.

3 - WHENEVER YOU HANDLE A FIREARM, OR HAND IT TO SOMEONE, MAKE SURE IT IS COMPLETELY UNLOADED.  Always open the action immediately, and visu­ally check the chamber. Make certain that they do not inadvertently contain any ammunition. Always keep the chamber empty and "safety" in the "on safe" position unless shooting is imminent. 

4 - DO NOT TRANSPORT ANY LOADED FIREARM. 

Keep all firearms unloaded during transport, whether stored in a holster, gun case, scabbard or other container.

5 - HUNTING FROM ELEVATED SURFACES SUCH AS TREE STANDS IS DANGEROUS. 

Doing so may increase the risk of handling a firearm. The following rules should always be observed by you and those you hunt with: Always make certain that the stand being used is safe and stable. Always make certain that your firearm is unloaded when it is being taken up and down from the stand. Always make cer­tain that your firearm is not dropped from the stand, or dropped while it is being taken up or down from the stand. Remember, a loaded firearm may discharge when dropped, even with the safety in the "on safe" position. 

6 - BEWARE OF BARREL OBSTRUCTIONS, FOR THE SAFETY OF BOTH YOUR GUN AND YOURSELF. Mud, snow, and an infinite variety of other objects may inadvertently lodge in a barrel bore. It takes only one small obstruction to cause dangerously increased pressures that can ruin (swell or rupture) the finest shotgun barrels. 

BEFORE CHECKING FOR A BARREL OBSTRUC­TION, BE CERTAIN YOUR FIREARM IS FULLY UNLOADED. 

Make sure no live rounds are in the chamber(s). Place the safety in the "on safe" position.

After assuring yourself that the firearm is completely unloaded, again, open the action, and look through the barrels to be sure they are clear of any obstruction. If an obstruc­tion is seen, no matter how small it may be, clean the bore with a cleaning rod and patch as described later in this manual. Before the first firing, clean both bores with a cleaning rod and patch, and wipe away any anti-rust compounds in the action / chamber areas.

7 - ALWAYS COMPLETELY UNLOAD YOUR SHOTGUN WHEN NOT IN USE.

As a safety precaution, it is preferable to disas­semble your gun for storage. Your responsibilities do not end when your firearm is unat­tended. Store your firearm and ammunition separately and well beyond the reach of chil­dren. Take all safeguards to ensure your shot­gun does not become available to untrained, inexperienced or unwelcome hands.

8 - USE THE PROPER AMMUNITION. The barrel and action of all Browning fireams have been made with substantial safety mar­gins over the pressures developed by estab­lished American commercial loads. Nevertheless, Browning assumes no liability for incidents which occur through the use of car­tridges of nonstandard dimensions which de­velop pressures in excess of commercially available ammunition which has been loaded in accordance with standards established by  the Sporting Arms and Ammunition Manufacturers' Institute (SAAMI) 

BE ALERT TO THE SIGNS OF AMMUNITION MALFUNCTION. If you detect an off sound or light recoil when a shell is fired, DO NOT LOAD AN­OTHER SHELL INTO THE CHAMBER. Open the action and remove the shell from the chamber. With the action open, glance down the barrel to make sure that an obstruction does not remain in the barrel. If there is an obstruction, completely clear the barrel before loading and firing again. Failure to follow these instructions can cause extensive damage to your gun and possible serious injury to yourself and others.

MAKE SURE OF ADEQUATE VENTILATION IN THE AREA THAT YOU DISCHARGE A FIREARM. WASH HANDS THOROUGHLY AFTER EXPO­SURE TO AMMUNITION OR CLEANING A FIREARM. 

Lead exposure can be obtained from discharg­ing firearms in poorly ventilated areas, cleaning firearms or handling ammunition. Lead is a substance that has been known to cause birth defects, reproductive harm and other serious injury. 

9 - NEVER INSERT A SHELL OF THE INCORRECT GAUGE IN ANY SHOTGUN. 

The gauge of your shotgun is marked on the side of the barrel. Store all shells of different gauges in completely separate and well-marked containers. Never store shells of mixed gauges in a common container or in your pockets. 

EXAMINE EVERY SHELL YOU PUT IN YOUR GUN. NEVER PUT A 20 GAUGE SHELL IN A 12 GAUGE GUN.

The most certain way to bulge or rupture a shot­gun barrel is to drop a 20 gauge shell into a 12 gauge chamber. The 20 gauge shell, unfortu­nately, will not fall completely through the bar­rel; its rim is caught by the front of a 12 gauge chamber. Your gun will misfire (with the chamber appearing to be empty). It is then possible to load a 12 gauge shell behind the 20 gauge shell. If the 12 gauge shell is then fired, the re­sult will be a so-called "12-20 burst" which can cause extensive damage to your gun and pos­sible serious inju1y to you and others. 

10 - USE SHELLS OF THE CORRECT LENGTH.

Do not use 3 1/2" shotgun shells in a shotgun or barrel with a 2 3/ 4" chamber or 3" chamber. Do not use 3" shells in a shotgun chambered for 2 3/4" shells. Doing so can result in a build­up of dangerously high pressures that may damage your gun and possibly cause serious injury to yourself or others. 

The size of the chamber is inscribed, along with gauge and choke designations, on the side of the barrel. The Gold semi-auto is chambered for 3" 12 or 3" 20 gauge loads. 

11 - DO NOT SNAP THE FIRING PIN ON AN EMPTY CHAMBER - THE CHAMBER MAY NOT BE EMPTY! Treat every gun, with the respect due a loaded gun, even though you are certain the gun is unloaded. 

12 - KEEP YOUR FINGERS AWAY FROM THE TRIGGER WHILE UNLOADING AND LOADING, UNTIL YOU ARE READY TO SHOOT.

13 - BE SURE OF YOUR TARGET AND BACKSTOP - Particularly during low light periods. Know the range of your ammunition. Never shoot at water or hard objects. 

14 - ALWAYS UNLOAD THE CHAMBER AND MAGAZINE BEFORE CROSSING A FENCE, CLIMBING A TREE, JUMPING A DITCH OR NEGOTIATING OTHER OBSTACLES.  Never place your loaded rifle on or against a fence, tree, car, or other similar object. 

15 - WEAR EYE AND EAR PROTECTION WHEN SHOOTING. Unprotected, repeated exposure to gunfire can cause hearing damage. Wear ear protectors (shoot­ing ear plugs or muffs) to guard against such damage. Wear shooting glasses to protect your eyes from flying particles. Allow proper distance (eye relief) between the scope and your eye when firing a scoped rifle or shotgun. Always keep a safe distance between the muzzle of your firearm and any persons nearby, as muzzle blast, debris and ejecting shells could inflict serious injury. Also, wear eye protection when disassembling and cleaning your shotgun to prevent the possibility of springs, spring-tensioned parts, solvents or other agents from contacting your eyes. 

16 - DROPPING A LOADED GUN CAN CAUSE AN ACCIDENTAL DISCHARGE.

This can occur even with a firearms "safety" in the "on safe" position. Be extremely careful while hunting or during any shooting activity, to avoid dropping any firearms. 

17 - IF YOUR SHOTGUN FAILS TO FIRE, KEEP THE MUZZLE POINTED IN A SAFE DIRECTION. 

Hold this position for a minimum of 30 seconds. Carefully open the action and remove the car­tridge. If the primer is indented, the cartridge should be disposed of in a way that cannot cause harm. If the primer is not indented, your firearm should be examined by a qualified gunsmith and the cause of the malfunction should be corrected before further use.

18 - BE DEFENSIVE AND ON GUARD AGAINST UNSAFE GUN HANDLING AROUND YOU AND OTHERS. 

Don't be timid when it comes to gun safety. If you observe other shooters violating any of these safety precautions, politely suggest safer handling practices. 

19 - BE CERTAIN YOUR SHOTGUN IS UNLOADED BEFORE CLEANING

Because so many gun accidents occur, when a firearm is being cleaned, special and extreme care should be taken to be sure your gun is unloaded before disassembly, cleaning and reassembly. Keep ammunition away from the cleaning location. Never test the mechanical function of any firearm with live ammunition.

20 - TEACH AND SUPERVISE FIREARMS SAFETY TO ALL MEMBERS OF YOUR FAMILY-ESPECIALLY TO CHILDREN AND NONSHOOTERS.

Closely supervise newcomers to the shooting sports. Encourage enrollment in hunting / shooting safety courses. 

21 - NEVER DRINK ALCOHOLIC BEVERAGES OR TAKE ANY TYPE OF DRUGS BEFORE OR DURING SHOOTING.

Your vision and judgment could be dangerously impaired, making your gun handling unsafe to you and to others. 

22 - PERFORM PERIODIC MAINTENANCE - AVOID UNAUTHORIZED SERVICING! 

Your new firearm is a mechanical device which will not last forever, and as such, is subject to wear and requires periodic inspection, adjust­ment, and service. Browning firearms should be serviced by a Browning Recommended Ser­vice Center or by Browning's service facility in Arnold, Missouri. Browning cannot assume any responsibility for injuries suffered or caused by unauthorized servicing, alterations or modifica­tions of Browning firearms. 

23 - READ AND HEED ALL WARNINGS in this instruction book, on ammunition boxes and with all accessories that you install on your firearm. It is your responsibility to secure the most up-to­-date information on the safe handling procedures for your Browning gun. Browning assumes no liability for incidents which occur when unsafe or improper gun accessories or ammunition combi­nations are used. 

24 - BROWNING RESERVES THE RIGHT TO REFUSE SERVICE ON FIREARMS THAT HAVE BEEN ALTERED, ADDED TO OR SUBSTANTIALLY CHANGED. 

Removal of metal from barrel(s), or modifications of the firing mechanism and / or operating parts may lead to Browning's refusal of service on such firearms. Browning will charge the owner for parts and labor to return the firearm to original Browning specifications.

Read and heed all warnings in this instruction book, on ammunition boxes and with all accessories that you install on your firearm. It is your responsibility to secure the most up-to-date information on the safe handling procedures for your Browning gun. 

Browning assumes no liability for incidents which occur when unsafe or improper gun accessories or ammunition combinations are used. 

DO NOT, UNDER ANY CIRCUMSTANCES, ALTER THE TRIGGER OR OTHER PARTS OF THE FIRING MECHANISM OF THIS OR ANY OTHER FIREARM. FAILURE TO OBEY THIS WARNING MAY RESULT IN INJURY OR DEATH TO YOURSELF OR OTHERS. 

In conventional gun terminology, the position and movement of gun parts are described as they occur with the gun horizontal and in normal firing position; i.e., the muzzle is forward or in front; the buttstock is rearward or to the rear; the trigger is downward or underneath; the rib is upward or on top. For general parts nomenclature refer to Figure 1. The Browning Citori Plus shotgun is shown disassembled to the extent necessary in order to follow the instructions contained in this book (See Fig­ure 2 below). 

The serial number of your Citori Plus shotgun can be found on the top tang under the top lever. Record this number for future reference. 

All Citori Plus Models are designed to shoot and function with 2 3/4" 12 gauge trap loads only. Browning can assume no responsibility for incidents which occur through the use of cartridges of non­standard dimension or those developing pressures in excess of industry standards established by the Sporting Arms and Ammunition Manufacturer's Insti­tute (SAAMI). 

CAUTION: DO NOT USE 3" OR 3 1/2" SHOTGUN SHELLS IN ANY SHOTGUN OR BARREL WITH A 2 3/4" CHAMBER. THE SIZE OF THE CHAMBER IS INSCRIBED ALONG WITH GAUGE AND CHOKE DESIGNATIONS, ON THE SIDE OF THE BARREL. 

Various exposed metal parts of your new gun have been coated at the factory with a rust preventative compound. Before assembling your Citori Plus shotgun, clean the anti-rust compound from the inside of the bar­rel, receiver and the action-chamber areas. Wipe clean the metal surfaces at the rear of the forearm, on the barrel lug and the interior areas of the re­ceiver, as well as any other parts coated with this compound. Browning Oil is ideal for wiping and cleaning these parts and for giving your gun its first lubrication. 

Clean the barrels using a cleaning rod and patch as explained under "Cleaning Suggestions.'' Read this entire manual, especially, "General Operating Proce­dures," before performing the first cleaning, to learn necessary information on breaking open the action, etc. 

BEFORE BEGINNING THE ASSEMBLY PROCESS, ALWAYS MAKE CERTAIN THERE ARE NO SHELLS IN THE CHAMBERS. 

1 - After wiping the mechanism clean, place one or two drops of a quality oil, like Browning Oil, on the following surfaces (See Figures 3-A, 3-B & 3-C):

3-A) Forearm Bracket

3-B) Barrel lug, hinge pin, bearing surface, Ejector slide, Barrel flats

3-C) Hinge pin, Cocking lever, Locking bolt.

2 - To attach the barrel to the action, grasp the stock's pistol grip with your right hand and an­chor the buttstock between your right forearm and right side. With the thumb of your right hand, move the top lever sideways to the ex­treme right (See Figure 4). 

3 - Grasp the barrels in your left hand and engage the barrel lug's circular recess with the action's hinge pin (See Figure 5). Keep pressure on the barrels to keep the hinge pin aligned in the bar­rel lug's circular recess, and simultaneously ro­tate the barrels upward, fully closing the actions (See figure 6). 

4 - Release the top lever. It should snap back to its central position.

5 - Place the butt of the gun's stock against your upper leg to support it. Engage the rear portion of the forearm to the front, radius area of the receiver (See Figure 7). 

6 - Pivot the forearm up to the barrels tightly. This will cause the takedown lever latch -to engage onto the barrels. It may be necessary to depress the takedown lever latch. It should be flush with the wood on the underside of the forearm. The forearm and latch can be installed in one motion by positioning the forearm as shown and tapping the forearm's widest part sharply toward the bar­rels with the heel of your hand (See Figure 8). the takedown lever should then automatically lock into position.

CAUTION: WHEN ASSEMBLING YOUR CITORI PLUS TRAP GUN, DO NOT USE UNDUE FORCE IN CLOSING THE ACTION. If the ac­tions and barrels are not properly aligned, un­due force will only cause them to grind together and score or mar the finely fitted surface. If there appears to be interference, start over at step 2, being careful to mate and align the barrel lug and the receiver hinge pin properly. 

Disassembling your Citori Plus into two parts - the action / buttstock and the barrel / forearm - is ideal for storage or for cleaning and maintenance. 

BEFORE BEGINNING THE DISASSEMBLY PROCESS, ALWAYS MAKE CERTAIN THERE ARE NO SHELLS IN THE CHAMBERS. 

1. With the action closed, anchor the gun's buttstock against your upper leg and pull the takedown lever latch outward. At the same time grasp the forearm with the other fingers of your left hand. With the help of your right hand, pivot the forearm away from the barrel (See Figure 9). Set the forearm aside. 

2. Break open the action in the usual manner. Then carefully disengage the barrel lug from the hinge pin and lift the barrels upward out of the action. 

3. Reattach the forearm to the barrels as explained previously, except with the barrels separated from the receiver. This is an ideal way to store your shotgun - in two pieces. 

The complete action (both barrels) is put "on safe" by drawing the thumb safety / selector rearward (See Figure 10). To put the gun "off safe" the safety / se­lector is moved forward. In the "on safe" position, an ''S" appears directly in front of the safety / selec­tor. 

The above applies whether the selector is posi­tioned for the "O" (over barrel) or "U" (under barrel) to fire first. Whenever you are not actually filing your shotgun, always be certain that your gun is pointed in a sale direction, and check the safety manually or visually to avoid any chance of acci­dental discharge. Always keep your safety in the "on safe" position unless you are actually firing the shot­gun. 

LOAD YOUR CITORI PLUS TRAP GUN ONLY WHEN SHOOTING IS IMMINENT. ONCE LOADED, THIS GUN IS READY TO FIRE BY MOVING THE SAFETY TO OFF SAFE, AND PULLING THE TRIGGER. 

Always keep the muzzle of your shotgun pointed down range at all times when on the shooting line. When leaving or moving along the line always open the action. Never have the action of your Citori Plus closed except when you are on the line, ready to shoot, when your gun is cased, or when it is set in a gun rack at the range. When you retrieve your gun from its case or from a gun rack, always immediately open the action and check to assure that no shells are in the chambers. 

Highly skilled techniques of hand-fitting and polish­ing have been used to accomplish the hairline fining of metal parts on this gun. These painstaking operations are necessary to prevent looseness, even after long use. You may consider your new gun to be slightly stiff. This close fitting, however, assures you of long lasting dependability. 

OPERATION OF THE TOP LEVER

The top lever operates the locking bolt, which is very closely hand-fitted to its barrel lugs. Provision is made for the gradual wear of locking surfaces by allowing a slight excess of metal. This exacting metal allowance keeps the breech of the gun tight for many years. 

Upon closing your gun, let the top lever snap into position - do not retard its action with your thumb. If closed in this manner, the top lever spring will re­turn the top lever mechanism to the locked position. It is not necessary that the top lever return to a completely central position; in fact, it usually will not do so in a new gun. Many experienced shooters culti­vate the habit of lightly pushing the top lever to the left after the gun is closed. It becomes automatic and is a quick method of assuring yourself that foreign matter has not interfered with the complete closure of the breech. 

The breech is so tightly hand-fitted that foreign mat­ter, sand, etc. may prohibit complete closing. 

IF THE BREECH WILL NOT CLOSE COMPLETELY, UNDER NO CIRCUMSTANCES SHOULD YOU ATTEMPT TO FIRE. 

Break the gun and unload it. Carefully examine the breech surfaces, and remove the foreign matter. Remember to always keep the polished breech sur­faces clean and lightly oiled. 

LOADING

CAUTION: AT ALL TIMES DURING THE LOADING AND UNLOADING PROCEDURES, BE SURE YOUR MUZZLE IS POINTING DOWN RANGE IN A SAFE DIRECTION, AND THAT THE SAFETY IS IN THE "ON SAFE" POSITION. 

1. Break the action as explained above. 

2. Insert a cartridge fully into each chamber. 

3. Close the action by pulling up on the forearm. The lever will snap back to center when prop­erly dosed. 

UNLOADING

1. Open the action by pushing the top lever to the right, as explained previously.

2. Pull down the forearm to eject the shell(s). The Citori Plus has an automatic, selective ejector. This means that a fired shell will eject com­pletely clear of the shotgun when the action is broken open. An unfired shell will be conve­niently elevated slightly out of the chamber for easy removal with your fingers. If you will be ejecting shells onto the ground, it is important to point the chambers - by slightly canting the shotgun to the right (left for left-handed shoot­ers) - so the shell(s) ejects clear of your body and face. 

3. Collecting empties with automatic ejectors­ - There is no disadvantage to having automatic ejectors when collecting empties. Simply brace the buttstock between your torso and forearm, and, after unlocking the action, cup your hand over the chamber before the action fully breaks open and the shell ejects. The shell will pop up into your hand for easy removal. 

Remember, never have the action of your Citori Plus closed except when you are on the line ready to shoot, when your gun is cased, or when it is set in a gun rack at the range. It is a courtesy to other shooters, and a wise safety practice, to keep your action open at all other times. 

FIRING YOUR CITORI PLUS

With the chambers loaded, the action closed, and the safety in the "off safe" position, the Citoi Plus is fired by simply pulling the trigger. Never pull the trigger unless the muzzle is pointed down range, at the clay target. Make sure people - other shooters, spectators, trap operators - are not down range. If there is any doubt about down-range safety, put the safety in the "on safe" position, and open the action immediately until you are certain all conditions are safe. 

Be certain you fully release the trigger between shots. If the trigger is not permitted to return to its fully forward position, the firing mechanism will not re-engage. This is the case with nearly all over under-shotguns with single-trigger systems. If this happens to you, remember, there is nothing mechanically wrong with your shotgun. You simply need to remember to fully allow the trigger to return forward before pulling the trigger for your second shot.

BARREL SELECTOR

Before you shoot you should select which barrel you want to fire first. This is done with the barrel selector. It is the same button utilized for the safety. On the right side of the safety is an "O" and on the left is a "U". One of these letters is covered while the other is exposed. When the "O" is showing, the "over" barrel will fire first. When a "U" is showing the "under" barrel will fire first. Barrel selection can only be made when the safety is in the "on safe" position. After firing one barrel it is not necessary to move the safety / selector to fire the second barrel. Simply release the trigger to its original position and pull it a second time. You want to recall which choke tube you have installed in each barrel when selecting which barrel to shoot first.

The Browning recoil reducer will allow you to shoot more, with greater comfort, than every before thought possible. It reduces recoil to your shoulder by splitting the single, large jolt of normal recoil into two smaller impulses, reducing peak recoil by up to 45% - all in a design that is virtually maintenance-free. The internal mechanism has no hydraulic or pneumatic parts to leak or wear out. Under normal use no maintenance is required. The entire mechanism is lubricated at the factory with an advanced silicone based grease. No other lubrication should ever be necessary under normal conditions. In the highly unlikely event that you experience a problem with our recoil reducer, take your Citori Plus to an authorized Browning Service Center or send it to our facility in Arnold, Missouri.

Length of pull is adjusted by screwing the recoil pad and plate in or out on the threaded inner cylinder extending from the recoil reducer. Recoil pad cant is set by angling the recoil pad with respect to the stock, and securing it with a set screw.

The recoil pad plate has three threaded holes for inserting a set screw and securing the recoil pad plate to the recoil reducer inner cylinder. These holes allow you to set the angular cant of the recoil pad: for Right Hand, Left Hand, or Neutral Position. Each position has its designation inscribed on the recoil plate adjacent to its threaded hole (See Figures 11 and 12). There are three perpendicular grooves traversing the threads on the inner cylinder. Each threaded hole corresponds to a groove depending on the setting of the recoil pad for cant. Your Citori Plus comes with one set screw, prepositioned and tightened down in the Neutral Position.

NEVER TIGHTEN THE SET SCREW DIRECTLY ONTO THE THREADS, AS THIS WILL DAMAGE YOUR GUN. 

When properly adjusted, the set screw will align perfectly with the proper groove. Several extra set screws are provided. Do not insert them into the re­coil pad plate holes at the same time. Only one set screw should be installed at any given time. The procedures for adjusting cant and pull are outlined below. 

BEFORE PERFORMING ANY ADJUSTMENTS, ALWAYS MAKE CERTAIN THERE ARE NO SHELLS IN THE CHAMBERS. 

LENGTH OF PULL

The Citori Plus comes with the recoil pad set in the neutral cant position. Length of pull comes set, from the factory, at approximately 14 1/4". Maximum pull is approximately 14 1/2" and minimum length is ap­proximately 14". To adjust the length of pull: 

1. Loosen the set screw in the recoil pad plate us­ing the smaller Allen wrench provided (2mm). The set screw is in the hole designated "Neutral Position" on the right side of the recoil pad plate on your new Citori Plus. 

2. To shorten the length of pull turn the pad clock­wise. Each turn represents 1/20''. To lengthen, turn the pad counterclockwise. When shortening the length of pull do not turn the pad bracket down the inner cylinder past the point where resistance to turning is encountered (See Figure 13). When lengthening pull never unscrew the recoil pad plate excessively. Always leave at least four threads engagement between the plate and inner cylinder. An average length of pull for most shooters of 14 1/ 4" is set when approximately five threads are showing. 

ANGULAR CANT

This allows you to cant the recoil pad to the right or left-depending on whether you are right or left handed-or leave it in the neutral position. It is usually easier to determine and set your length of pull before setting angular cant. 

1. Make sure the set screw on the inner cylinder is removed or loosened enough that it will not contact the threads on the inner cylinder. Use the 2mm allen wrench supplied. 

2. For right-handed shooters, line up the set screw hole marked Right Hand with the groove closest to it (See Figure 14). The Right Hand hole is lo­cated on the upper left side of the recoil pad plate. This setting will lean the heel (top end) of the recoil pad slightly to the left (See Figure 15).

3. If you are left-handed, follow the above, except line up the Left Hand hole with the left hand groove (See Figure 16). The Left Hand hole is found on the bottom lelt side of the recoil pad plate. 

4. To place the recoil pad in the Neutral Position line up the Neutral Position hole and groove (See Figure 17). The Neutral Position threaded hole is found on the right side of the recoil pad plate. 

5. With the hole lined up with the corect groove, insert the set screw and tighten it down­ through the recoil pad plate and down into the groove-using the small allen wrench. (If the set screw was already partially screwed into one of the other threaded holes for a different Cant setting you will need to remove it and move it to the correct hole.) 

Citori Plus Schematic Page 

Schematic is provided for parts identification only and should not be used as a guide to assemble guns. 

IMPORTANT: When ordering parts, list part numbers, part name, gauge, model and serial number. 

CAUTION: Browning parts are made exclusively for Browning guns and are not recommended for use in other guns even though models may be similar. Inadequately fitted parts may be dangerous. 

This adjustment allows you to achieve a perfect fit of the stock against your face. This is a most crucial adjustment, as it determines how correctly and con­sistently your eye will line up with the sight plane along the barrel rib. A Citori Plus correctly adjusted for cast on and cast off will have you looking directly down the center of the rib with the front and middle beads in alignment. 

Cast on and off is not affected by any changes in point of impact made at the rib. To adjust cast on and cast off perform the following: 

BEFORE PERFORMING ANY ADJUSTMENTS, ALWAYS MAKE CERTAIN THERE ARE NO SHELLS IN THE CHAMBERS. 

1. Loosen the two stock adjustment set screws on the right side of the removable cheek piece and remove the cheek piece by lifting upward (See Figure 18). This exposes the Cast On and Cast Off adjustments mechanism. the cheek piece comes set frorn the factory with cast in the cen­ter position.

2. Loosen both of the stock adjustment stud screws located in the top of the stock adjustment studs using the larger (3mm) allen wrench provided (See Figure 19). It takes about a 1/4" tum to loosen them adequately. 

3. Slide each stud equally in the desired direction. Each mark indicates 1/16".

4. Move the studs to the right for Cast Off.

5. Move the studs to the left for Cast On.

6. Right handed shooters may desire some Cast Off,  with left handed shooters preferring sonic Cast On. The terminology is the same for right­ or left-handed shooters. The net effect is to move the cheek piece to allow the face to move farther over the stock for better eye-to-rib align­ment. 

7. When properly set, the front and rear sight beads should line up perfectly each time you shoulder your shotgun. 

8. Tighten the stock adjustment stud screws. Be careful not to over tighten.

9. Replace the cheek piece onto the studs. If drop at comb has already been set to your desired height, tighten the two stock adjustment set screws securely. If drop has not been set, leave the set screws loose and proceed to "Adjusting Drop at Comb" below. 

Adjusting the drop at the cornb allows you to align your eye perfectly with the plane of the rib. A cor­rect sight picture for most shooters should have you looking down the rib with the bottom of the front bead resting on the top of the middle bead. This forms a "figure eight" or "stacked" configuration. Some of the rib will be showing as you look down the rib, but no rib will show between the beads. The important thing is to line up correctly each time you shoot. 

The drop measurement is determined by measuring the distance between the plane formed by the top of the rib and the top of the cheekpiece itself. The higher the cheekpiece, the lower the drop. To set drop perform the following: 

BEFORE PERFORMING ANY ADJUSTMENTS, ALWAYS MAKE CERTAIN THERE ARE NO SHELLS IN THE CHAMBERS. 

1. Loosen the two stock adjustment set screws on the right side of the cheekpiece (if they were not left loose after setting the Cast). The cheekpiece will now move freely, up and down on the stock adjustment studs.

2. Remove the cheekpiece completely off of the buttstock by lifting it straight up. If it won't remove, loosen the stock adjustment set screws until it can be removed. 

3. Insert the smaller (2mm) allen wrench (pro­vided) into the drop stop adjustment screw located in the center of the drop stop nut, found on the underside of the cheekpiece (See Figure 20). 

4. Turn it counterclockwise to raise the drop stop screw, and, in turn reduce the drop at the comb. The more the drop stop screw protrudes from the bottom of the cheekpiece, the less drop at the comb. This is because the end or the drop stop screw will limit how far down you can in­sert the cheek piece as you reinstall it on the stock. 

5. To increase drop, turn the screw clockwise up into the cheekpiece. Do not continue turning clockwise past the fully down position (this is when the drop screw is flush with the bottom of the cheekpiece. In this position the cheekpiece will rest on the stock.) DROP ADJUSTMENTS ARE A MATTER OF TRIAL AND ERROR. Adjust a little at a time until you obtain the desired sight picture on the rib. 

6. Once your desired drop at comb is obtained, reinstall the cheekpiece on the stock adjustment studs and then secure the cheekpiece in place by tightening the two stock adjustment set screws on the right side of the cheekpiece. Drop is now set on your shotgun. Do not set drop by moving the cheekpiece up and down and simply securing it with the stock adjustment set screws without using the drop stock screw. Unless the cheekpiece is positioned all the way down, flush with the stock, YOU MUST ALWAYS LEAVE THE DROP STOP SCREW AD­JUSTED SO IT CONTACTS THE DROP STOP PLATE, limiting the downward movement of the check piece at the drop position you determine. 

BEFORE PERFORMING THESE AND ANY ADJUSTMENTS, ALWAYS MAKE CERTAIN THERE ARE NO SHELLS IN THE CHAMBERS. 

Point of impact is determined by patterning a shot­gun and determining the relationship between where you were aiming and where the actual center of the pattern is. The Citori Plus comes preset with point of impact approximately 6" above the point of aim at 40 yards. Point of impact above the actual aiming point allows you to keep the clay bird in view constantly - just above the rib - as you swing and shoot 

The Citori Plus has a point of impact adjustment range of approximately 3" to 12" above point of aim. Two approximate ranges of adjustment are available: 3" to 9" and 6" to 12". Changes are accom­plished, across the full range, by a combination of turning the rear adjustment screw, and moving the muzzle end of the rib to either the higher or lower setting. Use the following to help decide what ad­justments will be necessary. 

CHANGING THE POSITION OF THE RIB AT THE MUZZLE END

The rib at the muzzle end has two holes-one slightly higher than the other. Removing the pin and realigning the holes to the slot in the front rib post changes rib height at the muzzle. Your Citori Plus comes with the rib in the down position at the muzzle. With it in this position, you have an approximate point of impact adjustment range from 6" to 12" above point of aim. If you desire to change the range to 3" to 9", or later return it to the original setting, perform the following: 

1. Place your Citori Plus securely in a padded vice, if possible. (If no vice is available lay it on a sur­face that will not mar the finish and hold the shotgun securely.) 

2. With the special Citori Plus rib punch (supplied) and a light hammer, tap out the pin holding the rib to the front rib post (See figure 21). This punch is designed to make this change easy and to avoid any possibility of marring the rib. 

NOTE: Although rarely necessary, at this point the rib itself is nearly ready to be removed entirely from the barrel. When performing point of irnpact adjustments only, it is never necessary to remove the rib. For a thorough cleaning of the rib adjustment mechanisms, it may be helpful in some cases. See "Removing and Reinstalling the Rib," below, for instructions. Otherwise, proceed to step three for adjusting point of impact. 

3. To set the floor of the rib in the higher position, lift up with the slot in the rib post (See Figure 22-A). To set the rib in the down position (as it comes from the factory) align the upper hole in the rib with the slot in the post. The rib is pushed all the way down onto the rib post in this position (See Figure 22-B). The amount of vertical change from one setting to the next may seem small, but it results in an approximate 3" change in point of impact.

4. To secure your setting, insert the punch in one end of the roll pin and place the pin in the de­sired hole. Using a light hammer, tap the roll pin into position. Once in position, with no portion of the pin protruding from either side, the change is completed. 

MAKING SMALL ADJUSTMENTS AT THE REAR OF THE RIB

The lib is adjustable from the rear of the rib, in ap­proximately 1/2" increments, by turning the rib elevator screw in or out. As you turn the screw you will hear and feel a click. Each click represents ap­proximately 1/2" adjustment in point of impact at 40 yards. You may use the screwdriver blade found on the Invector Plus choke tube wrench (supplied) to make the adjustment. 

1. To set a specific point of impact, first set the front rib position (if necessary) to the range of adjustment you will need (see above). 

2. Insert the screwdriver end of the lnvector Plus tool into the rear elevation screw (See Figure 23). Then turn the screw fully down (if it is not already in that position). This will put point of impact at 6" above (with front of rib set down) or 3" above (with front of rib set up). It makes it easier to turn the screw in by pressing lightly down on the rib when lowering it. 

3. Turn the screw out (counterclockwise) to raise point of impact. Remember, each click represents 1/2" movement. Turning the screw in (clockwise) lowers point of impact. Do not force the screw after reaching its maximum up / down travel. 

4. When your desired point of impact is achieved, the rib requires no further settings. The click mechanism is made to tightly hold point of impact at your desired setting. 

5. Resetting the drop adjustment in the moveable cheekpiece may be necessary whenever the plane of the rib is changed to alter the point of impact. 

REMOVING AND REINSTALLING THE RIB

It is never necessary to remove the rib for adjusting point of impact. To remove the rib for cleaning (if ever necessary), carefully perform the following to make sure no parts are marred or damaged: 

1. Raise the rear of the rib by turning counterclock­wise on the rear elevation screw until it is as high as it will go, as explained in step two un­der "Making Small Adjustments at the Rear of the Rib." Do not force.

2. Remove the roll pin at the front of the rib as explained in steps one and two under the sub­heading "Changing the Position of the Rib at the Muzzle End."

3. Lift up on the muzzle end of the rib about 30° Carefully lift the rib forward and out from the rear rib elevator housing. Never attempt to remove the rib by lifting on the front of the rib without the rear rib adjustment fully raised.

4. With the rib removed be careful not to lose the rib pivot. It is the circular part with a shoulder on each side that is fitted into the rib. It is easily removed and reinserted.

5. Removing the rib exposes the elevator detent spring which is inserted large end first into the groove in the rear rib elevator housing, with the bend facing up. It is unnecessary to remove this spring. Clean and lightly oil all rib components as necessary. 

6. To reinstall, make sure the elevator detent spring is installed properly and the elevation screw is turned fully counterclockwise. Insert the rear of the rib into the rib elevator housing with the front of the rib up about 30°. Make sure that the shoulders on the rib pivot are aligned with the grooves in the rear rib elevator housing. Lower the front of the rib down onto the front rib post and secure the front of the rib with the pin at the appropriate setting as explained previously. 

Your gun may or may not have optional barrel port­ing. The drilled holes in the top of the barrel are de­sired by some shooters for their tendency to reduce barrel jump and give a feeling of lower recoil against the face. They require only an occasional cleaning as described under "Cleaning Suggestions" later in this manual. 

Your Citori Plus is provided with the Invcctor Plus screw-in choke tube system. You can confirm this by reading the inscription on the right side of the barrel. The words INVECTOR PLUS mean your shot­gun uses a choke tube system designed for use in Browning 12 gauge shotguns with back-bored bar­rels. The extra length, combined with special tube tapers, gives you the finest possible patterns for tar­get shooters. Plus, you retain the same choke-switching convenience of the standard Invector system. lnvector Plus Tubes are fully steel and lead shot compatible. A special "Plus" choke tube wrench is provided to remove and tighten these tubes. This wrench also has a screwdriver end for performing rib adjustments. 

CAUTION: INVECTOR-PLUS TUBES ARE FOR USE IN BROWNING SHOTGUNS WITH BROWNING BACK-BORED BARRELS ONLY 

(.745" + 0- .005), AND ARE NOT INTERCHANGE­ABLE WITH REGULAR 12 GAUGE INVECTOR CHOKE TUBES. DO NOT USE INVECTOR PLUS TUBES IN BARRELS THREADED FOR STANDARD INVECTOR TUBES. DO NOT USE STANDARD INVECTOR TUBES IN BARRELS THREADED FOR INVECTOR PLUS TUBES. FAILURE TO FOLLOW THESE WARNINGS MAY CAUSE DAMAGE TO YOUR GUN AND CAUSE INJURY TO YOURSELF AND OTHERS. 

DO NOT FIRE THIS SHOTGUN WITHOUT HAVING BOTH INVECTOR PLUS CHOKE TUBES IN­STALLED. PERMANENT DAMAGE MAY RESULT TO THE THREADS. 

DO NOT USE BROWNING INVECTOR CHOKE TUBES IN ANY SHOTGUN BARRELS NOT SUPPLIED BY BROWNING. ALSO, DO NOT USE ANY OTHER CHOKING DEVICE IN ANY SHOTGUN BARRELS SUPPLIED BY BROWNING. USE ONLY THE APPROPRIATE GAUGE AND TYPE OF CHOKE TUBES MARKED INVECTOR PLUS. 

CAUTION: WHENEVER HANDLING ANY SHOT­GUN FOR THE PURPOSE OF REMOVING OR INSTALLING A CHOKING DEVICE, MAKE ABSOLUTELY CERTAIN THE GUN IS FULLY UNLOADED, AND THE ACTION IS BROKEN OPEN! NEVER ATTEMPT TO REMOVE OR INSTALL A SHOTGUN CHOKING DEVICE ON A LOADED FIREARM! 

TUBE REMOVAL - 

1. Fully unload your Citori.

ALWAYS UNLOAD YOUR CITOR/ PLUS FULLY. INSPECT THE CHAMBERS TO MAKE SURE THEY DO NOT CONTAIN ANY SHELLS.

2. Open the action using the top lever as explained previously.

3. Use the lnvector wrench to loosen the tube, turning it counterclockwise. Finger twist the tube the rest of the way out of the barrel. 

TUBE INSTALLATION- - 

1. Fully unload your Citori.

ALWAYS UNLOAD YOUR CITORI PLUS FULLY. INSPECT THE CHAMBERS TO MAKE SURE THEY DO NOT CONTAIN ANY SHELLS.

2. Open the action. 

3. Before installing a tube, check the internal choke tube threads in the muzzle, as well as the threads on the Invector choke tube to be sure they are clean. Lightly oil the threads with an oil like Browning Oil. 

4. Using your fingers, screw the appropriate tube into the muzzle end of the barrel, tapered end first, notched end outward. When it becomes finger-tight, use the Invector choke tube wrench to firmly seat the tube. 

THE INVECTOR CHOKE TUBE SHOULD BE PERIODICALLY CHECKED TO ENSURE THAT IT IS TIGHT AND FIRMLY SEATED. BEFORE CHECKING, FOLLOW THE SAFETY GUIDELINES OUTLINED ABOVE. 

Replacement and additional tubes and wrenches are available from your Browning dealer, or by writing to the Browning Consumer Department and Canadian customers please call or write to Browning Canada Sports Ltd./Ltee.

Replacernent and additional tubes and wrenches are available frorn your Browning dealer, or by writing: 

INVECTOR TUBE IDENTIFICATION -

To identify individual lnvector tubes, refer to the abbreviated indications on the side of the tube, or use the identification mark(s) located on the top rim of each tube. (See Figure 24 above). 

SELECTING THE CORRECT INVECTOR TUBE -

Although your Citori Plus is designed for target use with lead shot loads, the Invector Plus choke system is fully compatible with factory steel shot loads as well. For your information only, on the chart above we have included steel shot information in addition to the lead shot choke / pattern specifications you will need. Both lead and steel designations have proven necessary for hunters using other Browning guns with standard lnvector and Invector Plus tubes because in any given tube, steel shot gives a different pattern than lead shot. In fact, even larger steel shot diameters result in different patterns than smaller steel shot sizes. Each designation is in­scribed on each choke tube. Remember you will only need to refer to the lead shot designations when selecting a proper tube for your Citori Plus, as your new shotgun is not designed for any hunting use. 

The Citori Plus is a target gun, and as such will function better and more reliably over a longer period of time if it is properly maintained and kept clean. 

BEFORE PERFORMING ANY CLEANING PROCEDURES, ALWAYS MAKE CERTAIN THERE ARE NO SHELLS IN THE CHAMBERS. 

You should clean your Citori Plus after every day of shooting, and more often if it becomes excessively dirty. A minimum cleaning includes wiping down the action and oiling key parts. Most regular mainte­nance will also include cleaning the barrels. If you encounter a function problem (tight action when closing, etc.) be sure to give your gun a thorough cleaning, to see if it solves the problem, before seeking the services of a Browning Recommended Service Center or the Browning Service Facility in Arnold, Missouri, or a competent gunsmith. 

A light cleaning means oiling and wiping down. It can be accomplished with the barrels still attached. A full cleaning requires that you remove the barrels and forearm. To clean your firearm, follow the gen­eral outline below: 

CLEANING PROCEDURES -

BE CERTAIN YOUR GUN'S CHAMBERS ARE UNLOADED. ALWAYS WEAR PROTECTIVE SAFETY GLASSES DURING ALL ASSEMBLY, DISASSEMBLY AND CLEANING PROCEDURES. KEEP AMMUNITION AWAY FROM THE CLEANING AREA. DO NOT TEST THE FUNCTION OF YOUR FIREARM WITH LIVE AMMUNITION. 

1. Remove the barrels and forearm from the re­ceiver as explained previously.

2. Using a shotgun cleaning rod with a tip and patch large enough for a snug fit in the bores, insert the rod and lightly oil the patch in the breech end of the barrels and run back and forth several times in each barrel.

3. Inspect the bore from both ends for leading and plastic residue. Plastic residue is often left in the bores from the shot cups in modern shotshells. Leading and plastic residue will ap­pear as longitudinal streaks and are usually more predominant near the muzzles and just forward of the chambers. A normal amount of either is common and is not serious. If leading or plastic residue seems excessive you can re­move it by brushing the bores with a brass brush. Soak the brush or spray the bore with a powder solvent first. Scrub until clean. To prevent bristles from breaking off, push the brush fully through each time before pulling it back through. 

4. If your shotgun has barrel ports, carefully clean them with a rag soaked in powder solvents. You may need to scrape residues from the holes with something like a small screwdriver, pipe cleaner or small brush. If so, be careful not to mar the blueing on the barrels' outer surface, or scratch the inside of the barrels.

5. After all leading has been removed, the bore should be wiped dry with a clean patch, and then a lightly oiled patch run through it for preservation. 

6. Wipe all metal surfaces off the receiver, forearm, and barrels with a clean rag. Then lightly oil your gun at the points described in step 1 under "Assembly Procedures." Regular, light oiling is extremely important to the durability and reli­able operation of your shotgun.

7. Remember the broad, polished, finely fitted surfaces of the receiver and forearm mechanisms (the barrel lugs, the hinge pin and forearm bracket) must always have a thin film of oil. Use a quality oil like Browning Oil for this purpose.

8. Inspect the barrels and chambers. MAKE CERTAIN THAT NO PATCHES HAVE BEEN INADVERTENTLY LEFT IN THEM. Remove any that remain.

9. Wipe all wood surfaces with Browning Oil or a quality furniture polish, but not both. 

OTHER CLEANING SUGGESTIONS

• Never pour large quantities of oil into the re­ceiver or other parts. It can drain down to the wood and soften it - and cause permanent damage and loosening of the stock.
• It is very important that the chambers of your shotgun be cleaned thoroughly and promptly after shooting plastic shotshells. DO NOT LEAVE DISCHARGED (EMPTY) SHELLS IN THE CHAMBERS FOR ANY LENGTH OF TIME. The chemical composition of many plastic shells contains moisture which can "sweat" out of the shell and onto the chamber surface, and possibly cause corrosion and rust.
• The recoil reducer mechanism should never require any maintenance. In fact, attempting to oil it will wash away the lifetime lubrication already given it. Be sure to clean grit from in and around the mechanisms of the adjustable rib. Aerosol Browning Oil aids in keeping these parts clean.
• Occasionally remove the cheek piece and wipe the adjustment parts clean.

NEVER ATTEMPT TO TAKE YOUR CITORI PLUS APART FURTHER THAN EXPLAINED IN THIS MANUAL. 

This is a specialized, finely fined mechanism. You may permanently mar it by attempting to disas­semble the inner mechanism assemblies. If further disassen1bly for service or cleaning is required, take your gun to a Browning recommended Service Cen­ter or a competent gunsmith, or send it to our Arnold, Missouri Service Facility as explained under "Service or Repair." 

BROWNING RESERVES THE RIGHT TO REFUSE SERVICE ON FIREARMS THAT HAVE BEEN ALTERED, ADDED TO OR SUBSTANTIALLY CHANGED. 

Removal of metal from barrel(s), or modifications of the firing mechanism and/or operating parts may lead to Browning's refusal of service on such fire­arms. Browning will charge the owner for parts and labor to return the firearm to original Browning specifications. 

CLEANING THE ACTION AND TRIGGER GROUP -

1. When the action becomes excessively dirty, remove the trigger group and bolt assembly from the receiver as explained under "Full Dis­assembly" section. Clean with an oil such as Browning Oil or a gun solvent as necessary, using an old toothbrush to loosen any caked-on grime. Wipe the receiver cavity clean. Lightly oil the cavity (aerosol Browning Oil is ideal) and wipe it dry. No further disassembly is required for cleaning. 

2. Reassemble the trigger group, bolt assembly, gas system and the barrel to the receiver as explained previously. Then wipe all exposed metal surfaces with an oiled cloth, making sure to wipe clean all finger marks where moisture will accumulate. 

3. The barrel and action should be inspected to assure that all cleaning patches have been re­moved and not inadvertently left in the barrel or action. 

CLEANING THE GAS SYSTEM -

1. Remove the gas piston and piston sleeve from the magazine tube. Spray the magazine tube with a good quality powder solvent and wipe clean. 

2. Spray the piston and piston sleeve with a good powder solvent and brush it thoroughly to re­move any deposits (an old toothbrush is ideal). Spray the inside and wipe off any buildup. It will be easier to remove the piston sleeve spring to clean the interior of the piston sleeve. NEVER use a steel brush on any of the gas components. 

3. Complete the cleaning of the gas system by applying a very light film of Browning Oil to all parts for protection and lubrication. 

DO NOT TAKE YOUR GUN'S ACTION APART BEYOND WHAT IS EXPLAINED IN THIS MANUAL. This is a specialized, finely fitted mechanism; an attempt to remove the inner mechanism may mar it for life. It is unnecessary, and may do damage to the inner mecha­nism, to disassemble it for routine cleaning and oiling. Of course, misfortunes (such as drop­ping your gun in water) require appropriate attention, and in such circumstances, we recommend you immediately take your gun to a competent gunsmith. 

If your firearm should require service or re­pairs, we suggest you first contact a local recommended Browning Firearms Service Center. Contact your Browning sporting goods dealer or call our Service Department for the address of the Service Center nearest you. Otherwise, you may send your firearm directly to our own Service department. For technical questions about your firearm or service call our Service Department. 

Browning Service Department 

3005 Arnold Tenbrook Road 

Arnold, Missouri 63010-9406 

Phone: 1-800-322-4626

Canadian Customers call or write: 

Browning Canada Sports Ltd. / Ltee,

5617 Chemin St-Francois 

St-Laurent, Quebec H4S 1W6 

Phone: (514) 333-7261 

When returning your firearm for servicing, you must do the following: 

• Be sure it is completely unloaded.
• Package it securely in a cardboard container.
• Enclose a letter with your firearm that clearly describes the trouble experienced and the repairs or alterations desired.
• If convenient, send a copy of the letter to us separately
• Never return ammunition with your firearm. It is against postal and most commerce regulations.

If you have any questions about this manual or about any other Browning products, call or write our Consumer Information Department: 

Browning Consumer Information

Morgan, Utah 84050 

Phone: (801) 876-2711

BROWNING CANNOT ASSUME ANY RESPONSIBILITY FOR INJURIES  SUFFERED OR CAUSED BY UNAUTHORIZED SERVICING, ALTERATIONS OR MODIFICATIONS OF BROWNING FIREARMS. 

Read and heed all warnings in your owner’s manual, on ammunition boxes and with all accessories that you install on your firearm. It is your responsibility to secure the most up-to-date information on the safe handling procedures for your Browning gun. Browning assumes no liability for incidents which occur when unsafe or improper gun accessories or ammunition combinations are used. 

Do not, under any circumstance, alter the trigger, safety or parts of the firing mechanism of this or any other firearm. Failure to obey this warning may result in injury or death to yourself or others.